MOTION PRO

The MOTION PRO Compression Tester Tool, equipped with 10 mm, 12 mm, and 14 mm adapters, delivers rapid, effortless engine compression checks for bo...

The MOTION PRO Spark Plug Socket™ Pro in 14 mm / 9/16" size is designed for use with a 3/8" square drive or 17 mm wrench. Featuring a cutting-edge ...

Designed for Harley-Davidson and Buell riders, this Side Case Puller kit includes a bracket, puller bolt, and set screws to tackle the removal of t...

The Deluxe Piston Pin Puller Tool tackles both full skirt and short skirt (slipper) pistons with ease. Designed to fit piston pins ranging from 12 ...

Designed for bold mechanics, this Flywheel Puller features a right-hand internal thread sized M38 x 1.5. Engineered from premium high carbon steel ...

Take on oil filter removal with confidence using this KTM-specific puller. Its conical point screw pierces and grips the filter's sheet metal end c...

Engineered for fearless mechanics, this Flywheel Puller features a right-hand internal thread sized M26 x 1.0. Crafted from premium high carbon ste...

Tackle flywheel or rotor removal with this rugged Flywheel Puller featuring a right-hand internal thread M28 x 1.0 and an M14 cap for added versati...

Conquer flywheel and primary gear removal with this tough Flywheel Puller and Gear Extractor. Made from premium high carbon steel and heat treated ...

Dominate flywheel and rotor removal with this rugged Puller featuring an internal thread of M50 x 1.5. Constructed from premium high carbon steel a...

This Motion Pro Flywheel Puller features a right-hand internal thread with M12 cap, measuring M28 x 1.0. Crafted from premium high carbon steel and...

The ForkTru™ Fork Alignment Tool fits fork legs from 27 mm to 62 mm and spans forks 140 mm to 220 mm (5.5" - 8.6") apart. This fast, straightforwar...

Mount Motion Pro’s 08-0114 T-Handle Rack anywhere with this rugged Wall Bracket—perfect for toolbox sides, walls, posts, or any flat surface. Built...

The Gear Jammer™ was crafted to tackle the primary gear on Honda CRF450R/X models but conquers almost any motor with ease. It locks gears tight for...

Designed for WP 4860 MXMA CC forks, this Compression Fork Bolt Removal Tool handles the installation and removal of the compression unit on the rig...

Engineered for Honda CR models, this Seal/Bearing Retainer Tool tackles 47 mm lock rings with fierce precision. Designed to remove and install rear...

The 17 mm Float Bowl Shock Wrench is your go-to for removing float bowl drain plugs and fine-tuning high-speed compression on Showa, KYB, and WP re...

Flywheel puller featuring a right-hand internal thread of M33 x 1.5, precision laser-etched with the Motion Pro logo and part number. Designed to c...

25 mm wheel bearing removal tool built tough with heat treatment for maximum durability and extended service life. Ready to face the toughest jobs ...

Master any fastener with the Dual-Drive Allen T-Handle – 6 mm Ball Point Hex. This powerful T-handle gives you the grip to tighten or loosen bolts ...

Dominate fastener tasks with the Dual-Drive Allen T-Handle – 4 mm Ball Point Hex. This T-handle lets you swiftly tighten or loosen shaft fasteners,...

Conquer every challenge with this four-piece Dual-Drive Allen T-Handle set - sizes 4, 5, 6, and 8mm. The T-Handle design gives you solid grip power...

Take charge with the Combo Hex Bit Tool in 3 mm and 4 mm sizes. Designed to fit perfectly into the Motion Pro® Deep Socket and T-Handle Wrench, it ...

Master wheel bearing removal with this rugged eight-piece metric set, featuring sizes 10, 12, 15, 17, 20, and 25 mm. Equipped with both large and s...